first layer not sticking to the bed

…The first layer (of the raft) looks great, but nothing after that sticks. I tried: switching to new filament, did 2 cold pulls (not…

Still open · Printer prints only candy floss · 3D Printing Stack Exchange, 2024 · 2 posts · answered on skewray’s post, CC BY-SA 4.0

…So I made the change in my slicer but even then the first layer was visibly underextruding and it jammed soon after. I took…

Still open · Creality CR-10 Clogs and Underextrusion - Filament at fault? · 3D Printing Stack Exchange, 2018 · 3 posts · answered on arunabha42’s post, CC BY-SA 4.0

…bed. So you need a Brim and support: As OP found, a Brim is a setting that adds extra material in the first layer…

Still open · Retuning a very delicate and tricky print after print failure · 3D Printing Stack Exchange, 2020 · 2 posts · answered on David West’s post, CC BY-SA 4.0

…If you print with a first layer height of 0.3mm, bed levelling only needs to be approximate. If that doesn't work, and…

Still open · Can't get bed to level properly · 3D Printing Stack Exchange, 2020 · 5 posts · answered on SirChryse’s post, CC BY-SA 4.0

…and flat against the bed. BUT I had to run the print three times because the filament would not stick to the glass. It…

Still open · Under-extrusion after a certain amount of successful layers? · 3D Printing Stack Exchange, 2020 · 5 posts · answered on Dmoore56’s post, CC BY-SA 4.0

…There are usually options available in slicer software to control the distance between the raft and the first layer of the print object. It…

…an entirely black layer, and a few layers with the symbols in negative space). One way that you might be able to achieve this…

Still open · 3D printing enclosure with LED indication symbols -- is this possible? · 3D Printing Stack Exchange, 2016 · 4 posts · answered on O.K.’s post, CC BY-SA 4.0

…order to promote sticking. In this following first picture, I attempted with a 240°C tip and a 150°C bed (above PP's…

Still open · What are the ideal print conditions for polypropylene? · 3D Printing Stack Exchange, 2018 · 5 posts · answered on CuriouSir’s post, CC BY-SA 4.0

…or too close Z-leveling of the first layer. Make sure the model sticks to the bed, so that warped parts don't lift…

Still open · 3D Printer seem to "Forget" Tool Path · 3D Printing Stack Exchange, 2016 · 2 posts · answered on user4134’s post, CC BY-SA 4.0

…It would also seems like your heat bed may be too close to the printer or out of level which prvents proper sticking or…

…of getting the bed flat, the dimensions accurate, and figuring out the secret to getting the first layer to stick (with the sad realization…

Still open · Why do 3D Printers Suck? Please share your user experience · 3D Printing Stack Exchange, 2017 · 3 posts · answered on AdamP’s post, CC BY-SA 4.0

…extra filament sticks to nozzle forming 'big bomb' and end up with screwed printout due to layers shift) Printer: Qidi X-Plus Slicer: Qidi…

Still open · PET-G grid print problem · 3D Printing Stack Exchange, 2020 · 2 posts · answered on Mac’s post, CC BY-SA 4.0

…The first picture in the set is particularly interesting for a number of reasons: The chequered pattern of the top layer looks like being…

Still open · Ultimaker Original+: print has lumps and small gaps are being filled · 3D Printing Stack Exchange, 2018 · 2 posts · answered on pookie’s post, CC BY-SA 4.0

…print bed for maximum strength, and if possible use an undersized hole as a starting point/guide. Drilling horizontally may cause the layers to…

Still open · Drilling 3D-printed plastic · 3D Printing Stack Exchange, 2020 · 7 posts · answered on Tony Hansen’s post, CC BY-SA 4.0

…In addition to insulating from convective heat loss, I'm also considering using a layer of reflectix in there somewhere to reflect radiant heat…

Still open · Can I insulate my van's floor UNDER the bottom, in the undercarriage? · Motor Vehicle Maintenance & Repair, 2019 · 4 posts · answered on Ricardo Decal’s post, CC BY-SA 4.0

…I first thought this was down to bed adhesion, but I'm using a glue stick to make sure the print is unmovable and…

Still open · Visible/irregular horizontal lines for complex models · 3D Printing Stack Exchange, 2022 · 2 posts · answered on uorbe001’s post, CC BY-SA 4.0