bed leveling keeps drifting

I have a DIY 3D printer that uses a probe as z min limit and bilinear bed leveling. The problem is that bed leveling…

Still open · Bed leveling compensation not working! · 3D Printing Stack Exchange, 2019 · 1 posts · answered on 2012User’s post, CC BY-SA 4.0

…However when I try the bed levelling feature the first point (nearest to the origin), always starts with the probe out of the range…

Still open · Ender 3 CR Touch Bed Levelling X axis offset · 3D Printing Stack Exchange, 2023 · 1 posts · answered on Fusco Bhonsle’s post, CC BY-SA 4.0

…The bed leveling was done by the print nozzle being pushed down on the spring loaded bed and then the stepper will turn the…

Still open · Auto bed leveling with stepper motor lock · 3D Printing Stack Exchange, 2020 · 1 posts · answered on Willem van Tonder’s post, CC BY-SA 4.0

…Even as a last resort, I tried shimming the far-side bed screws and still have the same results after auto bed leveling. If…

Still open · Anycubic Kobra Go bed leveling · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Jeff Weber’s post, CC BY-SA 4.0

I have seen printers with table screws and bed leveling sensor and printers that have only bed leveling sensor (such as Prusa). So my…

Still open · How bed leveling is achieved without table screws? · 3D Printing Stack Exchange, 2018 · 2 posts · answered on OrElse’s post, CC BY-SA 4.0

…run in an enclosed heated chamber and I'm evaluating which bed leveling sensor I should use. I read that BLTouch and similar sensors…

Still open · What are pros and cons of piezo Vs strain gauges bed leveling sensors? · 3D Printing Stack Exchange, 2020 · 1 posts · answered on FarO’s post, CC BY-SA 4.0

I've added a G29 command in my starting script to do bed leveling process before every print. It works fine and compensates my…

Still open · Marlin Bed-Leveling Vs Skew Correction · 3D Printing Stack Exchange, 2019 · 1 posts · answered on 2012User’s post, CC BY-SA 4.0

…I want to try and use the bilinear bed leveling feature in Marlin but on a specific area of the bed. Something like that…

Still open · Marlin - G92 after bed levelling? · 3D Printing Stack Exchange, 2020 · 1 posts · answered on slepax’s post, CC BY-SA 4.0

I need Automatic Bed Leveling (ABL). I have seen this: FreeABL - the ultra cheap (free) ABL for Ender 3 . However, after reading the description…

…surface with the same "Z height" according to the LCD controller; I'm trying to determine whether this could be a bed-leveling issue).

…Is the glass bed absolutely level? Test with a metal ruler perpendicular to the bed. Maybe you clamped the glass bed to a n…

I decided to try and setup the bed auto level sensor. I downloaded this firmware: TEVO-Tarantula-I3-Marlin-Firmware and followed this tutorial…

Still open · Tevo Tarantula incorrectly auto leveling of bed · 3D Printing Stack Exchange, 2018 · 2 posts · answered on Jadeye’s post, CC BY-SA 4.0

I'm trying to revive an ender 3 I hadn't touched for some time, but I'm running into problems with bed leveling…

Still open · Bed leveling crashes marlin with M112 · 3D Printing Stack Exchange, 2025 · 2 posts · answered on user84207’s post, CC BY-SA 4.0

…yes Even with auto mesh bed leveling, you ought and should level the bed to a good degree to make the leveling not only…

I am trying to add auto bed leveling to my Prusa i3. When I run G28 my printer hits the X and Y end…

Still open · Printer goes beyond the bed when auto leveling · 3D Printing Stack Exchange, 2017 · 2 posts · answered on tosterovic’s post, CC BY-SA 4.0

Based on the following Start G-code, I want the print bed to heat up to the material_bed_temperature first then do the…

…And now when I do a bed leveling. Press leveling on the screen. the printer will go to the X and Y stops, the…

Still open · Bed crashing into print head when levelling · 3D Printing Stack Exchange, 2021 · 1 posts · answered on darranmead’s post, CC BY-SA 4.0

After leveling the corners of my bed (Ender 3 Pro, with Creality glass bed) the center of my bed is higher. When I start…

Still open · Glass bed is higher in center when corners are leveled · 3D Printing Stack Exchange, 2022 · 2 posts · answered on Squish’s post, CC BY-SA 4.0

…When Bed Leveling, the print head doesn't return left on the X-Axis although in the LCD display it does mark that the…

Still open · BLTouch on Bed Leveling check don't move left after point 6 · 3D Printing Stack Exchange, 2022 · 1 posts · answered on Eran Lahav’s post, CC BY-SA 4.0

…I tried leveling the bed manually before using ABL. Still had the same problem. Edit 2: I looked more closely at the bed leveling…

Still open · BLTouch does not compensate for bed level correctly · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Auri M’s post, CC BY-SA 4.0