bed leveling keeps drifting

…My current problem is that the script always does an auto bed leveling. I have two scripts to test this issue: LevelBed.gcode : Move…

Still open · Marlin firmware: move without auto bed leveling · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Endre’s post, CC BY-SA 4.0

…I'd like to stop the bed leveling before every print and to use the stored Mesh (UBL). Where and how do I do…

Still open · Disabling bed level before each print · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Chris Boring’s post, CC BY-SA 4.0

…It levels the bed and it starts printing too far away from the bed so it is just printing in the air. So, it…

Still open · Inconsistent Auto Bed Leveling - Having To Calculate Z Offset For EVERY Print · 3D Printing Stack Exchange, 2019 · 1 posts · answered on Rosalie W’s post, CC BY-SA 4.0

…I have also done the bed level and stored settings. Run the print and the nozzle is too high and therefore the filament doesn…

Still open · Nozzle too high after multiple bed level attempts · 3D Printing Stack Exchange, 2025 · 1 posts · answered on mreynol’s post, CC BY-SA 4.0

…I recently bought this auto bed levelling kit and these solid bed mounts for my Ender 3. I followed this Teaching Tech video as…

Still open · Creality Ender 3 EZABL bed levelling not working · 3D Printing Stack Exchange, 2020 · 1 posts · answered on jampez77’s post, CC BY-SA 4.0

…When I start the bed leveling it will go to the center, check it twice and then return to the home position. When I…

Still open · Ender 3 Pro with BLTouch bed leveling stops after 1 test (Marlin 2.0.7.2) · 3D Printing Stack Exchange, 2020 · 1 posts · answered on Paul’s post, CC BY-SA 4.0

When you have Auto Mesh Bed Leveling enabled on your printer, it's not possible to continue a failed print, is it? Continuing a…

Still open · Continuing a failed print when you have Auto Mesh Bed Leveling · 3D Printing Stack Exchange, 2022 · 3 posts · answered on Ageis’s post, CC BY-SA 4.0

…I'm using a Roko SN04-N NPN bed leveller. I've managed to set up 3 points bed levelling but I wanted to…

Still open · Where to define grid for bilinear levelling in Marlin · 3D Printing Stack Exchange, 2022 · 4 posts · answered on vale.maio2’s post, CC BY-SA 4.0

On an Ender 3 I leveled the bed and did test prints (the concentric squares), and the test is perfect. Then I run the…

Still open · Leveled bed but nozzle too distant · 3D Printing Stack Exchange, 2025 · 1 posts · answered on Mauro’s post, CC BY-SA 4.0

Due to a mains power failure, I was unable to finish a "Thingiverse Stripes" auto bed levelling test on my new Ender 3 v2…

Still open · I'm new to 3D Printing and I've have just assembled a new Ender3 V2 with a CR Touch bed leveller. The extruder motor is not working · 3D Printing Stack Exchange, 2022 · 1 posts · answered on Tom’s post, CC BY-SA 4.0

…The probe is deployed once only while mesh bed leveling. How can I make the probe deploy twice at every point? Where am I…

Still open · How to probe twice while mesh bed leveling with a BLTouch setup? · 3D Printing Stack Exchange, 2021 · 2 posts · answered on boom_shiva’s post, CC BY-SA 4.0

I have an Ender 5 with an auto bed leveling sensor (TRU-LEV 600). It is working fine, however, as the sensor probes the…

Still open · Ender 5 hotend and bed cooling down while auto bed leveling · 3D Printing Stack Exchange, 2023 · 4 posts · answered on isaac7437’s post, CC BY-SA 4.0

Every time I try to level my Ender 3 v2 I get all the corners perfect when pulling paper in between. But for some…

Still open · Can level every where except the center of the bed · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Kone’s post, CC BY-SA 4.0

…To avoid confusion, the proper term for 'manually leveling' is 'bed tramming'. Some firmware has a 'Bed Tramming Wizard' like the Marlin-based mriscoc…

Still open · Using the BLTouch to assist with manual bed levelling? · 3D Printing Stack Exchange, 2023 · 2 posts · answered on geekgeek4’s post, CC BY-SA 4.0

…I use a 4 points auto bed leveling. And I have a systematic problem. Every time I try the bed leveling test, it seems…

Still open · Auto bed leveling: systematic slope · 3D Printing Stack Exchange, 2019 · 3 posts · answered on JPFrancoia’s post, CC BY-SA 4.0

The gold standard for levelling the bed on a resin printer seems to be using a sheet of paper. Is there any reason why…

Still open · Leveling a printer bed using the FEP in the tank? · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Aaargh Zombies’s post, CC BY-SA 4.0

…After sorting out some XY and probe offset issues, I just cannot get the bed levelling to seem to read the bed properly. Here…

Still open · Ender 3 Neo Bed Levelling just won't work any more · 3D Printing Stack Exchange, 2025 · 1 posts · answered on Adam Hey’s post, CC BY-SA 4.0

…Most "auto-leveling" is not leveling but compensation for a non-flat or non-level bed surface. It's helpful to beginners who don…

Still open · Are heated beds or auto-levelling systems worth paying extra for on an entry level filament printer? · 3D Printing Stack Exchange, 2021 · 4 posts · answered on Aaargh Zombies’s post, CC BY-SA 4.0

Every time I issue a G29 command the printer runs through all its multi-point/probing bed leveling routine. Is this normal? or can…

Still open · G29 UBL G-code - every request levels bed? · 3D Printing Stack Exchange, 2022 · 2 posts · answered on JRP’s post, CC BY-SA 4.0

…It works but has issues with auto bed leveling. Specifically, auto bed leveling does not compensate for bed tilt in X and Y directions…

Still open · Auto Bed Leveling does not compensate for bed tilt correctly (Anycubic Kobra Neo) · 3D Printing Stack Exchange, 2023 · 3 posts · answered on thebear8’s post, CC BY-SA 4.0