bed leveling keeps drifting

Any cubic Cobra was working fine till date now suddenly the head is hanging around 10 mm above the bed tried for auto leveling…

…Any hint about what to check? Is the obtained map indicating that the bed is already too leveled to act on any compensation? UPDATE…

Still open · Autobed leveling doesn't compensate · 3D Printing Stack Exchange, 2016 · 3 posts · answered on FeliceM’s post, CC BY-SA 4.0

…adhesion, nozzle to bed distance and overall level. Nozzle to bed distance needs to be the thickness of a plain A4 or Letter paper…

Still open · Filament moving around and not sticking to bed · 3D Printing Stack Exchange, 2019 · 4 posts · answered on Andrew Hawkins’s post, CC BY-SA 4.0

…Being a derivative fro Marlin firmware, the bed leveling speed in between probes can also be easily set in G-code. G-code G29…

…I re-levelled and turned the BLTouch off and levelled again in the hope that it would work like a manual bed levelling and…

Still open · Ender CR-10 Max with BLTouch won’t level · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Mjlawson91 ’s post, CC BY-SA 4.0

I have some issue with my BLTouch (I'm new to bed levelling) : I compiled Marlin 2.x (for my SKR 1.3) for…

Still open · BLTouch error Marlin 2.x (on SKR 1.3) · 3D Printing Stack Exchange, 2021 · 2 posts · answered on math45’s post, CC BY-SA 4.0

…This implies that constant MANUAL_BED_LEVELING is obsolete. It is not found anywhere else except for the file linked above. So, no , the…

Still open · Marlin Firmware Manual Mesh Leveling · 3D Printing Stack Exchange, 2018 · 2 posts · answered on cds333’s post, CC BY-SA 4.0

…I've calibrated esteps and levelled bed. It only seems to happen with this new filament

Still open · Why do segments of my print "pop" off the bed after a few layers? · 3D Printing Stack Exchange, 2021 · 1 posts · answered on jaywayco’s post, CC BY-SA 4.0

…I have a problem with the bed leveling test. The first test points are good, after that the nozzle try to test on the…

Still open · 3DTouch Probing Off the Bed X-axis · 3D Printing Stack Exchange, 2020 · 1 posts · answered on AlexPTC’s post, CC BY-SA 4.0

So, I recently installed an inductive sensor to my 3D printer for auto bed levelling and now I'm stuck on Z probe offset…

Still open · X axis doesn't lift after levelling · 3D Printing Stack Exchange, 2020 · 2 posts · answered on Potato Lord’s post, CC BY-SA 4.0

…Bend the aluminum bed until it is flat. Add a 5th leveling point under the middle of the bed. You could either make it…

Still open · Why is the center of my glass print bed lower than the corners? · 3D Printing Stack Exchange, 2021 · 4 posts · answered on SPJ’s post, CC BY-SA 4.0

After leveling the corners of the bed and doing a manual mesh bed leveling (both options on the menu LCD) I adjust the babystep…

Still open · Setting Z offset on Artillery Hornet (Marlin 2.0.7.2) · 3D Printing Stack Exchange, 2023 · 3 posts · answered on Pablo Reta’s post, CC BY-SA 4.0

…I think I can get around 90 % of my issues if I just ran a level X axis at the start then input a…

…I am working through the painstaking process of bed leveling, but even though Klipper seems happy with the level, my first layer calibration print…

Still open · Poor first layer even after careful calibration · 3D Printing Stack Exchange, 2024 · 2 posts · answered on rgov’s post, CC BY-SA 4.0

…Re-level your bed (hopefully you have already done this before asking this question). Add mesh bed leveling to your printer (don't know…

…Please don't suggest I level the bed - it is levelled, not gravitationally, but mechanically. I have tightened everything up. I have tried altering…

Still open · How to address bed scratching on a Creality Ender 3 · 3D Printing Stack Exchange, 2020 · 2 posts · answered on Dean Nicholson’s post, CC BY-SA 4.0

…nut (and washer) to come up with a makeshift solution, level the bed with a small wrench and print a replacement with a captive…

…I am using the CR Touch to level the bed. After a month of trying to fix the issue with the bed leveling, I…

Still open · Marlin 2.1.2.2 Ender 3 Pro CR touch does not work properly · 3D Printing Stack Exchange, 2024 · 2 posts · answered on XaniXxable’s post, CC BY-SA 4.0

…I believe I have leveled the bed correctly, I bought yellow bed springs, and I manually leveled before I set up the CR Touch…

Still open · Nozzle scraping bed on Ender 3 with CR Touch · 3D Printing Stack Exchange, 2022 · 2 posts · answered on kahalani’s post, CC BY-SA 4.0

…I have an inductive bed leveling probe and each time I remove the plate the Z offset seems to be off on the next…

Still open · Starting G-code for auto Z probe offset · 3D Printing Stack Exchange, 2019 · 2 posts · answered on CEO’s post, CC BY-SA 4.0