bed leveling keeps drifting

I have the problem that the bed auto level functionality is working but not precise enough so that the first layer doesn't stick…

Still open · Creality CR Touch not precise enough · 3D Printing Stack Exchange, 2022 · 1 posts · answered on veio’s post, CC BY-SA 4.0

…solid bed mounts from TH3D, could the silicon ones I got on Amazon be the issue? Also I’m using Octoprint bed level visualizer.

Still open · Ender 3 V2 bed slanted · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Itsamemitch’s post, CC BY-SA 4.0

…Bed level From section 6 - Auto leveling of the user guide : Section 7 covers "Assisted Leveling" or manual leveling. Factory Reset Inexplicably , this isn…

Still open · Print nozzle too far from the plate · 3D Printing Stack Exchange, 2024 · 2 posts · answered on Cajun66’s post, CC BY-SA 4.0

…It sounds to me like your end-stops positions relative to your new bed level are off or the Z-offset is very off…

Still open · Ender 3v2 nozzle plunging into bed after finishing mesh (only changed springs) · 3D Printing Stack Exchange, 2023 · 3 posts · answered on Joleme’s post, CC BY-SA 4.0

…This bed is not leveled correctly It's clear from the video, that the bed is leveled far too low: the extrusion on the…

Still open · Why is my Ender 3 nozzle z-axis raising before printing? · 3D Printing Stack Exchange, 2024 · 3 posts · answered on user19201’s post, CC BY-SA 4.0

…auto bed leveling Now I'm thinking to myself... hey! auto bed leveling to the rescue! Well of course not. The 1x2 cm square…

Still open · Ender 3 S1 general (beginners) problems · 3D Printing Stack Exchange, 2023 · 2 posts · answered on DerpyNerd’s post, CC BY-SA 4.0

…Level the bed with the BLTouch (The Z offset is correct and 0 mm is basically at the print surface) Repeat the process above…

Still open · Marlin + BLTouch layer compression · 3D Printing Stack Exchange, 2022 · 1 posts · answered on Bob’s post, CC BY-SA 4.0

…Increase bed temperature (try 5 degrees steps) Clean the bed Check if the bed is completely leveled up. Increase the thickness of the first…

Still open · Poor adhesion on new layer - Monoprice mini select · 3D Printing Stack Exchange, 2020 · 4 posts · answered on Nick Santitoro’s post, CC BY-SA 4.0

After leveling the bed with a paper sheet, the nozzle starts on the right place, but 3 millimeters above the bed. sorry it is…

Still open · Anet A6 bed problem · 3D Printing Stack Exchange, 2025 · 1 posts · answered on jerry’s post, CC BY-SA 4.0

…After that set the Z-offset using a paper and run some bed adhesion test prints and use babysteps. Level and probe your bed…

Still open · Ender 3 PRO BLTouch V2 perfect on center with small prints but fails on corners or big prints · 3D Printing Stack Exchange, 2020 · 3 posts · answered on Sheshman’s post, CC BY-SA 4.0

…I have levelled my bed and set the coordinates to (0, 0, 0) with the nozzle paper’s thickness away from the bed. When…

Still open · Printing above, not onto the bed · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Joshua’s post, CC BY-SA 4.0

…print starts without moving to the other corners and auto leveling the bed. Does the new version of cura require me to turn the…

Still open · Printrbot simple metal not auto leveling · 3D Printing Stack Exchange, 2016 · 2 posts · answered on Dana’s post, CC BY-SA 4.0

…Can anybody tell me what these defects are caused by? It looks like your build-plate (print bed) is out-of-level. Specifically, your…

Still open · What are these defects caused by? · 3D Printing Stack Exchange, 2023 · 2 posts · answered on tmighty’s post, CC BY-SA 4.0

…Maybe the sensor got knocked out of the way or someone thought it was funny to turn your bed-level-wheels and turned them…

Still open · Ender 3 Pro suddenly printing too high! · 3D Printing Stack Exchange, 2025 · 2 posts · answered on silv3rsid3up’s post, CC BY-SA 4.0

…Make sure the bed is level; what is meant that the bed is relatively level with respect to the nozzle, not water bubble level…

Still open · Adhesion problem (heat bed or extruder issue) · 3D Printing Stack Exchange, 2018 · 2 posts · answered on dale’s post, CC BY-SA 4.0

…yesterday, and I spent a while trying to level it, but if I move the bed too low when it moves it gets stuck…

Still open · How to stop scratching the bed and print properly on an Ender 3 V2 · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Mason Walker’s post, CC BY-SA 4.0

Here is my first attempt at printing a "Bed Leveling Calibration test". It obviously didn't come out as I would have hoped, but…

Still open · Adhesion problem when printing calibration test · 3D Printing Stack Exchange, 2019 · 2 posts · answered on kane’s post, CC BY-SA 4.0

…However, from what I can tell, there is no way any of the printers out there (Creality, and others) to actually level the bed…

Still open · Why use G29 during a print? · 3D Printing Stack Exchange, 2020 · 2 posts · answered on Fred Lackey’s post, CC BY-SA 4.0

…I have manually leveled the bed over and over again, added a glass sheet over the bed, applied masking-tape and what-not. The…

Still open · Tevo Tarantula I3 filament clogging up · 3D Printing Stack Exchange, 2018 · 2 posts · answered on Jadeye’s post, CC BY-SA 4.0

I had a couple of recent nozzle/bed crashes, so I now frequently do a manual bed levelling. I do these while the bed…

Still open · Ender 3 Z-limit now unreliable - possible causes and solutions? · 3D Printing Stack Exchange, 2022 · 7 posts · answered on iCollect.it Ltd’s post, CC BY-SA 4.0