bed leveling keeps drifting

…to be a bunk bed for two kids. The lower mattress (120 x 160cm) is at the floor level. The frame material is 70x70mm…

Still open · Is this bunk bed design feasible? · Woodworking Stack Exchange, 2016 · 1 posts · answered on Petteri H’s post, CC BY-SA 4.0

…Hope this helped! Level the bed Make sure that the bed is level. The nozzle must be equally high over heated surface, otherwise only…

Still open · How to get Sunlu PLA to adhere to the printing bed? · 3D Printing Stack Exchange, 2021 · 4 posts · answered on Anonymous _User’s post, CC BY-SA 4.0

…In other words, over extrusion during the first layer improves print stickiness, so that close bed leveling gives sticky prints but first layer over…

Still open · Which type of extrusion problem? · 3D Printing Stack Exchange, 2016 · 4 posts · answered on Veda’s post, CC BY-SA 4.0

…E-Steps extruding a perfect 100 mm in/out Bed is perfectly Leveled to 0.1 mm Auto leveler Z offset also set so…

Still open · Unusual printing after upgrading · 3D Printing Stack Exchange, 2022 · 2 posts · answered on kris stankievech’s post, CC BY-SA 4.0

…I use 7x7 mesh bed leveling. Reran calibration wizard.

Still open · Prusa i3 MK3S supports fail to print on bed · 3D Printing Stack Exchange, 2020 · 1 posts · answered on Marco’s post, CC BY-SA 4.0

…See it as an automated process to add automatic bed levelling to a number of printer models. To change the bed probing area, you…

Still open · Setting the startpoint of the EZABL 3x3 mesh · 3D Printing Stack Exchange, 2019 · 2 posts · answered on d mcatee’s post, CC BY-SA 4.0

…There could be multiple reasons for this happening, the most probable cause would be that the bed isn't leveled properly, if you have…

Still open · First layer problem · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Hazem Ismail’s post, CC BY-SA 4.0

…I set the bed temp to its defined temp. Then I auto-level the bed. Then I heat the nozzle up to its defined…

Still open · Cura variables and initial G-code commands · 3D Printing Stack Exchange, 2022 · 3 posts · answered on RayW’s post, CC BY-SA 4.0

…The next step is to also ensure the bed is level (unless you have auto-levelling). If the bed is level, then you need…

Still open · Prints fail to adhere to build plate · 3D Printing Stack Exchange, 2021 · 4 posts · answered on leowrites’s post, CC BY-SA 4.0

…Bed Z http://marlinfw.org/docs/features/lcd_menu.html#tune Per description in this table, this refers to the Mesh Bed Leveling process…

Still open · Marlin "Tune->Bed Z" vs "Tune->Babystep Z" vs Z Offset? · 3D Printing Stack Exchange, 2019 · 2 posts · answered on cds333’s post, CC BY-SA 4.0

…I just bought an Elegoo Mars 2 Pro and had trouble getting it to stick to the bed, after some painful bed leveling and…

Still open · What causes the FEP to be dented during resin printing? · 3D Printing Stack Exchange, 2021 · 3 posts · answered on Ryan Vella’s post, CC BY-SA 4.0

The stock heated bed which came on my Creality printer is significantly warped beyond any simple leveling with the screws. Lets say I want…

Still open · Premium heated bed upgrade options? · 3D Printing Stack Exchange, 2019 · 2 posts · answered on cds333’s post, CC BY-SA 4.0

I just upgraded my CR-10 to a 32-bit board with Marlin and a BLTouch for bed-leveling. Here is my process: Run…

Still open · Z-Probe height isn't working · 3D Printing Stack Exchange, 2021 · 2 posts · answered on SvdSinner’s post, CC BY-SA 4.0

…From this morning onward, anything that I try to print comes out like this, I've been trying to level the bed better which…

Still open · What would cause my 3D printer to start printing badly from one day to the other? · 3D Printing Stack Exchange, 2025 · 4 posts · answered on Juan Pablo Bustos Paulich’s post, CC BY-SA 4.0

…There is no auto bed leveling and I have done my best to tweak it by hand using the screws underneath the heated bed…

Still open · What causes this characteristic pattern and what is it called? · 3D Printing Stack Exchange, 2020 · 2 posts · answered on Zhro’s post, CC BY-SA 4.0

…0.4 mm nozzle PLA Temperatures nozzle temperature 210 °C bed 70 °C 0.12 mm layer height manual bed leveling 30 mm/s…

Still open · Ender 3 nozzle moves through previous layer on lithophane · 3D Printing Stack Exchange, 2020 · 1 posts · answered on ry_ol’s post, CC BY-SA 4.0

I have a Creality CR-10 with EZABL (bed leveling sensor). I'm not sure what prompted the printer to think the center is…

Still open · How can I get my printer to home correctly? · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Jack Harris’s post, CC BY-SA 4.0

…I have tried my best to level the bed but I am an amateur I was originally getting poor adhesion so I cleaned the…

Still open · Why are my layers messy and curling off the print bed? · 3D Printing Stack Exchange, 2020 · 5 posts · answered on Deep’s post, CC BY-SA 4.0

…However, the Ender 6 has 5-point assisted leveling, 4 corner and the middle of the bed. It is not capable to map the…

Still open · Z-axis compensation · 3D Printing Stack Exchange, 2022 · 2 posts · answered on Beenum’s post, CC BY-SA 4.0

…During auto bed leveling seems like printer is trying to go outside x, y position of bed and make levelling there. By doing that…

Still open · Creality Ender 3 v2 and BLTouch v3.1 - issues with x, y axis - crashing to the printer's frame · 3D Printing Stack Exchange, 2021 · 1 posts · answered on kalko555’s post, CC BY-SA 4.0