bed leveling keeps drifting

…nozzle is "touching" the bed during proces, and not going below the bed level) - then homing may be correct. Otherwise do troubleshooting , as has…

Still open · 3D printer homing issue, nozzle damaging the bed when printing · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Fz6r Rider’s post, CC BY-SA 4.0

…When I try to run true bed leveling the Touch probes off of the bed like in the Reddit post "Ender 3 bltouch probes…

Still open · BLTouch probes off the print bed · 3D Printing Stack Exchange, 2022 · 1 posts · answered on quaternioneer’s post, CC BY-SA 4.0

…Only that even after re-leveling the bed several times it won't lay down a stable first layer unless I go into the…

Still open · How do I change and then save the Z offset on an Ender 5 Pro · 3D Printing Stack Exchange, 2024 · 2 posts · answered on Aaargh Zombies’s post, CC BY-SA 4.0

…The CR touch sensor touches the bed before the nozzle does. The bed is level, and the gantry isn't quite square (different issue…

Still open · Ender 3 S1 Pro Nozzle too high · 3D Printing Stack Exchange, 2025 · 5 posts · answered on Vandel212’s post, CC BY-SA 4.0

…I'm having trouble when using bed leveling. It homes everything correctly, and then moves outside the bed before the probe repeatedly deploys and…

Still open · BLTouch not leveling · 3D Printing Stack Exchange, 2020 · 2 posts · answered on AbberantAeons’s post, CC BY-SA 4.0

…I upgraded to a 32 bit Creality 4.2.7 and also purchased a BLtouch 3.1 bed leveling probe. I downloaded the stock…

…The job of "bed-leveling" is to make the realized z=0 plane to be identical with the bed. If you can, use a…

…This implies that if you are using bed leveling with a leveling sensor, after G29 or G28 (if you defined ENABLE_LEVELING_AFTER_G28…

Still open · Let the nozzle wait on the parking position · 3D Printing Stack Exchange, 2024 · 3 posts · answered on Mark’s post, CC BY-SA 4.0

…However I also noticed that after the automatic bed leveling any manual settings on the printer are reset to the G-code (I assume…

Still open · Prusa I3x and repetier host heat problems · 3D Printing Stack Exchange, 2018 · 2 posts · answered on James’s post, CC BY-SA 4.0

…All stock Ender 4 parts, no upgrades other then magnetic bed attached to a piece of steel. Bed was manually leveled and auto levels…

Still open · Ender 4 problem with printer stopping mid print · 3D Printing Stack Exchange, 2019 · 1 posts · answered on MeliJoe’s post, CC BY-SA 4.0

…If you print directly onto the metal build surface it would not matter if you use a(n automatic) bed levelling system because you…

Still open · Warped bed - bulge vs dip? · 3D Printing Stack Exchange, 2019 · 2 posts · answered on cds333’s post, CC BY-SA 4.0

…is the optimum bed and hot end temperature for maximum adhesion on a tall thin print with a low level of contact (corner piece…

…Sometimes heated beds are slightly larger than the actual print area. E.g. 235x235 mm or 310x310 mm. For centering the nozzle to the…

…This works fine for auto homing, bed levelling and using code G1 Z0 to lower to where needed. However when using Cura to print…

Still open · BLTouch calibrated, nozzle still dives into the bed · 3D Printing Stack Exchange, 2020 · 3 posts · answered on MattW49’s post, CC BY-SA 4.0

…nozzle, but instead by a mechanical or calibration issue, most likely gantry tilt, X-axis misalignment, or uneven bed leveling across the X-axis.

My Ultimaker 1 with a heated bed doesn't print good first layer lines at all. The single lines keep detaching from the printbed…

Still open · First layer lines don't stick at all · 3D Printing Stack Exchange, 2017 · 2 posts · answered on Markus Appel’s post, CC BY-SA 4.0

…the auto-level has improved anything. I've got single-layer test patterns that look OK on one part of the bed and look…

…I tried MK4Duo, but apparently there was no support for my auto bed leveler and the bed was coming up and hitting the nozzle…

Still open · Problem with print bed height on Creality Ender 4 · 3D Printing Stack Exchange, 2018 · 2 posts · answered on dusodesign’s post, CC BY-SA 4.0

…My bed temperature is set to 70 °C and the speed is 50 mm/s. I manually leveled it afer the self leveling didn…

Still open · How do I make the layers stick together more and warp less? · 3D Printing Stack Exchange, 2022 · 4 posts · answered on Guy Turner’s post, CC BY-SA 4.0

…anything and run the Bed Level Visualizer which will present a color graph representing the flatness of the bed. Image below from linked site…

Still open · Ender V3 SE middle of print bed sticking but fine elsewhere · 3D Printing Stack Exchange, 2024 · 2 posts · answered on heypresto’s post, CC BY-SA 4.0