bed leveling keeps drifting

…Can it be the mesh leveling that is acting up? How do I check that? The heat bed feels differently warm in different places…

Still open · First layer looks weird and print fails · 3D Printing Stack Exchange, 2020 · 5 posts · answered on GusOst’s post, CC BY-SA 4.0

…several pieces (represented by bed 1 in the image below) and the nozzle was below the level of the bed (I believed it had…

Still open · Thermal Stress Cracking During Heat-Up on Glass Heated Bed · 3D Printing Stack Exchange, 2020 · 4 posts · answered on Hyperion31415’s post, CC BY-SA 4.0

…Any ideas how to reduce those problems? This sounds like a bed leveling issue. As reported by others, I get much less warping with…

Still open · Problem printing bigger models in the Ender 5 · 3D Printing Stack Exchange, 2022 · 3 posts · answered on Cadu Oliveira’s post, CC BY-SA 4.0

…the auto-level matrix are usually at the same X, Y location (I circled it with a marker on the bed to be sure…

Still open · Should center point of G29 matrix always be zero? · 3D Printing Stack Exchange, 2021 · 1 posts · answered on satellite1217’s post, CC BY-SA 4.0

…bed quit and was replaced, I have had trouble with bed adhesion and printed first layer material warping using PLA and auto bed leveling…

Still open · Acceptable temperature variation in heated bed · 3D Printing Stack Exchange, 2021 · 2 posts · answered on David Pearson’s post, CC BY-SA 4.0

…will not adhere to the bed and forms a blob. You could consider decreasing the gap by leveling with a thinner piece of paper…

…The printer mentioned in the project is "Creality Ender 3 Pro printer with a metal extruder and a BLTouch auto bed-leveling sensor", which…

Still open · Figuring out differences between Creality Printers · 3D Printing Stack Exchange, 2022 · 2 posts · answered on Dave’s post, CC BY-SA 4.0

…They bed level squares that prints squares on all four corners and the centre of the bed plate. If I raise the offset any…

Still open · Ender 3 BLTouch first layer problems · 3D Printing Stack Exchange, 2019 · 4 posts · answered on Raph’s post, CC BY-SA 4.0

…After about 8 months I started noticing issues with my bed being weird and never really being level no matter how much time I…

Still open · Build plate (PEI on glass) isn't flat after several months of use? · 3D Printing Stack Exchange, 2020 · 4 posts · answered on Foible’s post, CC BY-SA 4.0

…I’ve also tried leveling the bed using Bed Leveling, creating a mesh to apply height adjustments during printing and saving the settings. When…

Still open · How to lower the nozzle height by 0.2 mm? · 3D Printing Stack Exchange, 2024 · 2 posts · answered on viikktor_’s post, CC BY-SA 4.0

My Creality CR-10 Smart 3D printer has built-in auto bed levelling (ABL). It appears that it is cannot do anything if ABL…

…Finally, I've got everything moving in the right direction, I got the auto-bed leveling (bilinear) going (did a 7x7 grid), saved the…

…All of the changes that I'm making relate to homing\nozzle position, in an attempt to level the bed and get the right…

…lower level is MDF, cork panel for heat insulation and thin (1.5-2mm) aluminum heated bed on top. I build an 18.5…

Still open · How thick does an aluminum print bed need to be · 3D Printing Stack Exchange, 2021 · 4 posts · answered on markshancock’s post, CC BY-SA 4.0

…using the leveling feature it goes to the X an Y physical end stops, then goes to the middle of the bed, a few…

…To solve the actual problem , you need to prepare the glass by cleaning it properly, use a level bed with a correct initial nozzle…

Still open · Altering the print bed temperature at different layers · 3D Printing Stack Exchange, 2020 · 3 posts · answered on cybernard’s post, CC BY-SA 4.0

…My leveling procedure is going through the manual leveling UX with the bed heated, sticking a piece of paper under the center and 4…

Still open · Small parts de-adhere halfway through print · 3D Printing Stack Exchange, 2023 · 3 posts · answered on javanix’s post, CC BY-SA 4.0

…It has drop down legs at the back but nothing except the jockey wheel at the front and I have no way of levelling…

Still open · Levelling a trailer with a pair of jacks · Motor Vehicle Maintenance & Repair, 2019 · 1 posts · answered on Lucy B’s post, CC BY-SA 4.0

…My bed is leveled with an index card. Any suggestions on what might be causing this issue. Bototm of part

Still open · Top and bottom of part not coming out smooth · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Carson’s post, CC BY-SA 4.0

…MANUAL_HOME_Z_POS , and; DELTA_SMOOTH_ROD_OFFSET See my answer to Delta printer nozzle not moving square with a perfectly level bed…

Still open · Delta Printer: After Calibration X and Y Axis are slightly different · 3D Printing Stack Exchange, 2019 · 2 posts · answered on dgrat’s post, CC BY-SA 4.0