bed leveling keeps drifting

…Ender 3 Leveling done via BLTouch (Z offset calibrated to be 0.1 mm from print bed) E steps calibrated properly Hotend temp: 200…

Still open · Ender 3 filament retracts on its own · 3D Printing Stack Exchange, 2023 · 2 posts · answered on SleepySheep200’s post, CC BY-SA 4.0

I am trying to compensate for bed leveling by measuring a mesh with my Z probe, a BLTouch, and I am unable to do…

Still open · CoreXY mesh probing issue · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Feynman137’s post, CC BY-SA 4.0

…same material, with the bed properly leveled (i.e. not smashing the nozzle into it again) and with the bed and nozzle temperature high…

Still open · What is this white layer on my 3D printer? · 3D Printing Stack Exchange, 2021 · 3 posts · answered on Yon’s post, CC BY-SA 4.0

…Also try printing the first layer slower or try adjusting the bed level offset so you are squishing the first layer down a bit…

Still open · How do I get circles on small interior holes to adhere to the bed? · 3D Printing Stack Exchange, 2019 · 5 posts · answered on Perry Webb’s post, CC BY-SA 4.0

…The only way I can even move where the hotend ends up after home, is by changing X_BED_SIZE and X_BED_SIZE…

Still open · Ender 5 Plus offset issue · 3D Printing Stack Exchange, 2020 · 1 posts · answered on Derple’s post, CC BY-SA 4.0

…Larry Wood via All3DP Before lowering the Z-endstop mount first screw in all the levelling/tramming screws under the build plate/heated bef…

Still open · Nozzle not level and first print failed · 3D Printing Stack Exchange, 2022 · 3 posts · answered on Sliced Water’s post, CC BY-SA 4.0

…4-5 A, while the bed needs to draw about twice that to heat a rated power level. Their recommendation is to switch this…

Still open · Bed Heating Failed, Printer Halted, Please Reset · 3D Printing Stack Exchange, 2021 · 3 posts · answered on Mallikarjun Talagade’s post, CC BY-SA 4.0

…Bed leveling etc and building the bed mesh all went OK. Slicer is Cura 4.7.1. However, it won't print. The Gcode…

Still open · Problem with Marlin 2.0.5.3 / BLTouch upgrade with Sovol SV01 · 3D Printing Stack Exchange, 2020 · 2 posts · answered on nmw01223’s post, CC BY-SA 4.0

…flashes and deploys twice but when I try to autohome or level or deploy it through options, menu probe autohomes X and Y axis…

Still open · Ender 3 board 4.2.2 BLTouch 3.1 crashes into bed during autoleveling · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Piotrekdoro’s post, CC BY-SA 4.0

…https://www.reddit.com/r/mpminidelta/comments/73xcxg/leveling_doesnt_seem_right/ https://www.reddit.com/r/mpminidelta/comments/6tqe7f/follow_up_on_bed…

Still open · Single point Z-correction after 3-point auto-leveling · 3D Printing Stack Exchange, 2017 · 2 posts · answered on Jan’s post, CC BY-SA 4.0

…nozzle temperature - 180, bed temperature - 65. I calibrated extuder according to the video. Bed level seems to be ok for me. I started using…

Still open · Creality CR-10 slightly jerks when moves from right to left · 3D Printing Stack Exchange, 2018 · 2 posts · answered on tiktak’s post, CC BY-SA 4.0

…I've got printers that do bed leveling cold but print with the correct initial Z height to get a perfect first layer. This…

Still open · Some procedures to improve 1st layer · 3D Printing Stack Exchange, 2020 · 2 posts · answered on Perry Webb’s post, CC BY-SA 4.0

…Leveling the bed maniacally several times (all the screws in the frame need to be very tight) Varying bed temperature and nozzle temperature at…

Still open · Anet A8 beginning layers not printing correctly · 3D Printing Stack Exchange, 2018 · 5 posts · answered on holi4683’s post, CC BY-SA 4.0

…set the Z offset and auto level the bed. My printer has other thoughts. Now my bed temperature will only heat up to 10…

Still open · Why does my Ender 5 Pro bed stop heating 10 °C below the set point? · 3D Printing Stack Exchange, 2021 · 3 posts · answered on Speedy06’s post, CC BY-SA 4.0

…Never tried but I'm guessing you would need to cool the bed, heat the part, and stick it back then reheat the bed…

Still open · What is the best way to adhere an old printed part to the bed? · 3D Printing Stack Exchange, 2021 · 4 posts · answered on rjj’s post, CC BY-SA 4.0

…swiping at start of print When I started work on mine, the bed leveling and radius (Delta-only issue) were horrid, and my erstwhile…

Still open · What tweaks do slicers use to get rafts to stick? · 3D Printing Stack Exchange, 2017 · 4 posts · answered on MrGlass’s post, CC BY-SA 4.0

…To increase the distance between the nozzle and the bed you can: level with a little thicker paper, move the bed down on all…

Still open · PLA Issue printing first 3 mm with Ender 3 Pro · 3D Printing Stack Exchange, 2020 · 3 posts · answered on eltrompeta’s post, CC BY-SA 4.0

…Are there any ways I can try to fix this? Something is wrong with your bed height, Z axis mechanics, or "automatic bed leveling…

Still open · Every time I print with my Ender 3 V2, I get a bubbly ring around the bottom. How can I fix this? · 3D Printing Stack Exchange, 2022 · 2 posts · answered on lil mikey’s post, CC BY-SA 4.0

…How is it that the auto tramming can report the corners of the bed to be level, and then immediately afterwards it produces this…

Still open · Uneven mesh after perfect auto tramming? · 3D Printing Stack Exchange, 2022 · 1 posts · answered on benram14159’s post, CC BY-SA 4.0

…The G28 initiates and homes, then the G29 does the 9 point bed leveling, then just sits there and does nothing. BLTouch behavior during…

Still open · BLTouch error causing bed and nozzle temp setpoints to change to zero · 3D Printing Stack Exchange, 2021 · 2 posts · answered on rsadler’s post, CC BY-SA 4.0