bed leveling keeps drifting

…now when I try to do Auto Home or Level Bed , nothing happens, no beeps no movement, and a minute later get "Homing failed…

Still open · Error message "homing failed printer halted please reset" · 3D Printing Stack Exchange, 2024 · 2 posts · answered on Laserman_UK’s post, CC BY-SA 4.0

…When I do not use the G29 command, Auto Bed Level, the printer won't print and just extrudes plastic in mid-air. But…

Still open · Extruder motor not functioning after G29 command · 3D Printing Stack Exchange, 2017 · 1 posts · answered on joebrad27 ’s post, CC BY-SA 4.0

…What's your heat bed temperature control software / how is it configured? FYI I use Marlin and I get these problems when I don…

Still open · Strange grooves with ABS · 3D Printing Stack Exchange, 2018 · 2 posts · answered on uiop’s post, CC BY-SA 4.0

…If the raft helps and the print eventually "heals up" and only the bottom few mm are bad, then you have a bed leveling…

Still open · Printerbot printing stringy · 3D Printing Stack Exchange, 2016 · 2 posts · answered on LN6595’s post, CC BY-SA 4.0

…to remove it just before leveling and printing starts. Furthermore, replace the heated bed connector and solder the bed power wires directly to the…

Still open · Anet A8 Hotbed Not Heating Correctly · 3D Printing Stack Exchange, 2018 · 2 posts · answered on kcthode’s post, CC BY-SA 4.0

…Tried both clean bed (water+detergent then isopropyl), and coating it with glue stick, problem persists. Having your printer properly calibrated, trammed and leveled…

Still open · Bad adhesion only when printing many small parts "all at once" - can't use Brim · 3D Printing Stack Exchange, 2023 · 2 posts · answered on SF.’s post, CC BY-SA 4.0

…looks like the nozzle is too far from the bed, try leveling the bed again - that should solve the problem. It may also be…

Still open · Under extrusion · 3D Printing Stack Exchange, 2020 · 4 posts · answered on Matthias Verstraete’s post, CC BY-SA 4.0

…Check the leveling of your bed occasionally and relevel the bed. By removing prints, one can easily unlevel it over time without noticing it…

Still open · Reasons for a PLA print not sticking to bed all the sudden? · 3D Printing Stack Exchange, 2019 · 3 posts · answered on Ultra Gamer’s post, CC BY-SA 4.0

…The part continues to get higher and higher than the wiper level, which doesn't make sense because the wiper wipes all the excess…

Still open · Top-Down SLA Printer Bulging Issue · 3D Printing Stack Exchange, 2020 · 2 posts · answered on Porter Morgan’s post, CC BY-SA 4.0

…First layer of bed level test ( this source ). The filament is nicely flat on the print bed, also it still sticks when I rub…

Still open · Massive blobs/under extrusion/"pearl necklace" only after first few layers (Ender 3 V2) · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Philipp Wacker’s post, CC BY-SA 4.0

…nice except when homing or leveling, then they sound like This is the end of one of the bed trying to heat up, I…

Still open · Ender 3 V2 with new SKR mini e3 v3 is heating up extremely slowly · 3D Printing Stack Exchange, 2023 · 1 posts · answered on selacey’s post, CC BY-SA 4.0

…I can tram the bed, but levelling is not starting from the center. I've tried the "Set Home Offsets" option in the menu…

Still open · Sprite Pro Kit Configuration Tips Needed · 3D Printing Stack Exchange, 2025 · 1 posts · answered on Adam Hey’s post, CC BY-SA 4.0

…glass beds - this would also make it easier to take them off the printer to clean without needing to re-level the bed every…

Still open · Using dollar-store picture glass for print bed on top of original heated aluminum bed? · 3D Printing Stack Exchange, 2017 · 6 posts · answered on BunnyKnitter’s post, CC BY-SA 4.0

…I overlap the blue tape ends to the bed so it sticks, then spray the hairspray onto the tape. Also bed leveling is super…

Still open · PLA and bed heating? · 3D Printing Stack Exchange, 2019 · 12 posts · answered on Thomas S.’s post, CC BY-SA 4.0

…The bed is tilted too much (there are 2 independent Z stepper motors) so that the trigger point is further that the maximum allowable…

Still open · Qidi Tech Q1 Pro throws error message when sending file to printer · 3D Printing Stack Exchange, 2025 · 2 posts · answered on ჩოპრექსა’s post, CC BY-SA 4.0

…bed leveling issue (or eventually bed is bent) caret mechanism issue (dispositioned/bent) You can also check different speeds just to be sure. This…

Still open · Prints get really messy for no apparent reason · 3D Printing Stack Exchange, 2016 · 4 posts · answered on DELTA12’s post, CC BY-SA 4.0

…It looks like your nozzle distance to the bed is still too high, so the extruded material does not start sticking to the bed…

Still open · "Blobs" at beginning and end of layer and no adhesion · 3D Printing Stack Exchange, 2022 · 2 posts · answered on Philipp Wacker’s post, CC BY-SA 4.0

I have an Ender 3v2 and I recently installed the CR Touch auto bed leveler. I was wondering how to add more probing points…

Still open · How to add more probing points on the CR Touch · 3D Printing Stack Exchange, 2022 · 2 posts · answered on chuy0414’s post, CC BY-SA 4.0

…Increased/decreased bed temperatures (I am using PLA filament), adjusted the bed level, Z-offset. Nothing seems to be working. After printing the printed…

Still open · Micro swiss direct drive for Ender 6 · 3D Printing Stack Exchange, 2022 · 2 posts · answered on Beenum’s post, CC BY-SA 4.0

…after a few layers this usually levels out. The initial distance between the nozzle and the bed usually is calibrated with the paper sheet…

Still open · Nozzle scratching on second layer · 3D Printing Stack Exchange, 2022 · 2 posts · answered on risiko24’s post, CC BY-SA 4.0