solved.

bed leveling keeps drifting

994 threads discussed this. Here is what worked. 1734 ms

Solved only

  1. I have had exactly the same experiences as you did with a inductive sensor on a Prusa i3 clone. It looks as though the bed leveling is not executed, or the level/mesh tilted.

    Marked as the answer · Automatic leveling probe offset; adjusting for one side ruins the other · 3D Printing Stack Exchange, 2018 · 3 posts · answered on Liam’s post, CC BY-SA 4.0

  2. As a guess, you are using the wrong command. If set for n x n grid, you get 3 point measurement with G29, but that is not auto leveling, it is just setting Z height - based on average height at 3 points.

    Marked as the answer · Bed leveling method not working with Repetier firmware 0.92.9? · 3D Printing Stack Exchange, 2016 · 3 posts · answered on xxx’s post, CC BY-SA 4.0

  3. Understanding the pattern Indeed, it looks like the error is induced by the X-Axis, as the pattern is very uniform over the Y-axis.

    Marked as the answer · Bed leveling suggestions given this mesh generated by BLTouch · 3D Printing Stack Exchange, 2022 · 2 posts · answered on cybernard’s post, CC BY-SA 4.0

  4. There is only one thing you can do if there are no more threads left on the levelling screws , you need to move the Z-end stop assembly (depicted in the front left of your photo) to a lower position.

    Marked as the answer · Ender 3 Pro has too much space between extruder and bed · 3D Printing Stack Exchange, 2023 · 4 posts · answered on Brad K’s post, CC BY-SA 4.0

  5. Basically, you are also using a probe, the nozzle is the probe. So this is very similar to an auto levelling setup using a capacitive or inductive sensor, the difference is that your M851 nozzle to probe distance is…

    Marked as the answer · Switch nozzle contact probe auto leveling with Marlin 2.0 · 3D Printing Stack Exchange, 2020 · 2 posts · answered on henradrie’s post, CC BY-SA 4.0

  6. First of all a caveat: Leveling an FDM printer ...is done differently than an SLA/DLP printer When calibrating an FDM printer, you align the bed with the X and Y axis, using a paper, metal shim or another tool (such as…

    Marked as the answer · Calibrating a resin printer · 3D Printing Stack Exchange, 2020 · 2 posts · answered on 0xF2’s post, CC BY-SA 4.0

  7. I could solve my problem by this strange system for both opposite sides but I couldn't find the really reson of this problem!:

    Marked as the answer · Strange leveling problem by PrusaI3 · 3D Printing Stack Exchange, 2017 · 4 posts · answered on WDR’s post, CC BY-SA 4.0

  8. material sticking problem can be due to following reason: bed level bed temperature z motion calibration (ex if not calibrated layer height is 0.2 and z move 0.4 then material cant stick on bed) bed surface (for…

    Marked as the answer · Filament lifts from the hot bed while printing · 3D Printing Stack Exchange, 2024 · 7 posts · answered on Peter’s post, CC BY-SA 4.0

  9. Printing some more parts tonight. Looks like solution is better bed "leveling" (tramming, or basically squareness between X, Y, and Z axis).

    Marked as the answer · Ripple in layers · 3D Printing Stack Exchange, 2019 · 3 posts · answered on CrossRoads’s post, CC BY-SA 4.0

  10. Just move the Z-endstop up a little higher, also make sure the bed leveling screws are not completely screwed in. So: Move the head of the printer up.

    Marked as the answer · Tevo Michelangelo nozzle below build plate? · 3D Printing Stack Exchange, 2018 · 2 posts · answered on some_user’s post, CC BY-SA 4.0

  11. Your video shows that your bed seems warped somewhat. Ammount of error As I assume you did level the bed with a sheet of paper to be 0.1 mm thick, we can estimate the change of thickness.

    Marked as the answer · Ender 3 distance between nozzle and bed changing on Y-axis · 3D Printing Stack Exchange, 2020 · 4 posts · answered on 1125’s post, CC BY-SA 4.0

  12. Read First Painters Tape does lift the print surface upwards by its thickness. This has to be accounted for in leveling the bed.

    Marked as the answer · What are the pros and cons of Painters tape? · 3D Printing Stack Exchange, 2020 · 2 posts · answered on Trish’s post, CC BY-SA 4.0

  13. There are a number of points missing, but I can offer a few suggestions. The re-leveling of the bed could have resulted in the bed now being in a position to block the nozzle. I have done exactly that in the past.

    Marked as the answer · Clicking noise from the extruder and no filament coming out · 3D Printing Stack Exchange, 2020 · 2 posts · answered on moulson13’s post, CC BY-SA 4.0

  14. as per base of the pink printout it looks like the bed is far below the nozzle (level the bed) to check the Z steps/mm setting, the best way will be to home it, then from menu move Z by 50mm and check with a ruler or…

    Marked as the answer · Problems with Z step · 3D Printing Stack Exchange, 2018 · 2 posts · answered on Juli15’s post, CC BY-SA 4.0

  15. You need to level you bed. Thin prints happen when the extruder is too low and is printing too close to the bed.

    Marked as the answer · Issue with 3D printer making super thin layers · 3D Printing Stack Exchange, 2020 · 3 posts · answered on Sapphethaz’s post, CC BY-SA 4.0

  16. I'm not claiming this is the definitive answer but I made a successful print with these changes. There were several things I did that may have helped but I don't think solved the problem.

    Marked as the answer · First layer disaster: auto-leveling the bed. Need guidance · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Nolan Robidoux’s post, CC BY-SA 4.0

  17. I had the exact same issue as you and had done all the fixes you mentioned. The only thing that solved it for me was to make sure the model in the slicing software was flat to the "bed".

    Marked as the answer · BLTouch not levelling correctly (it does seem to work, just not accurately enough) · 3D Printing Stack Exchange, 2022 · 3 posts · answered on Jasper Schulte’s post, CC BY-SA 4.0

  18. First, you should make sure that printing surface is adjusted correctly: it must be perpendicular to all three delta columns, all other adjustable parts must be checked and adjusted if necessary (depending on actual…

    Marked as the answer · how to level kossel's endstops? · 3D Printing Stack Exchange, 2017 · 2 posts · answered on Henry’s post, CC BY-SA 4.0

  19. The bed minimum temperature is defined in your configuration file, e.g.: If the error is displayed, it means that the measured temperature drops below this level.

    Marked as the answer · MINTEMP BED Fixed error when running consecutive print · 3D Printing Stack Exchange, 2020 · 3 posts · answered on wonton’s post, CC BY-SA 4.0

  20. If these were ceramic brake pads, they tend to smoke on first heavy use. Usually, if the shop which puts them in also beds the brakes, you won't see any smoke because they'll already have caused all the smoke.

    Marked as the answer · Brakes smoke on driver side, but only after non-level terrain · Motor Vehicle Maintenance & Repair, 2015 · 2 posts · answered on kec’s post, CC BY-SA 4.0