bed leveling keeps drifting

To help me with bed leveling my Ender 3 v2 (using stock Creality firmware, V1.0.2 ), I'm trying to write a G…

Still open · Wait for click to continue · 3D Printing Stack Exchange, 2021 · 2 posts · answered on nl-x’s post, CC BY-SA 4.0

…When I start printing, the first few levels go fine. But then the extruder starts slowly moving in the wrong direction and after a…

Still open · Movement of the extruder out of its original position during printing · 3D Printing Stack Exchange, 2021 · 1 posts · answered on David’s post, CC BY-SA 4.0

…Being so small, it doesn't like to adhere to the bed. I could probably resolve this by tightening up the bed level. However…

Still open · Slow down a specific set of extruder moves · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Joel Coehoorn’s post, CC BY-SA 4.0

…I would relevel the bed a bit further away, or (if you're happy with how actually level the bed is) set a Z…

Still open · Model stuck on the heating bed · 3D Printing Stack Exchange, 2020 · 4 posts · answered on Jahit’s post, CC BY-SA 4.0

…Bed leveling is a key step in print prep, and every printer behaves best with subtle changes to the bed leveling procedure. My guess…

Still open · My 3D printer hotend always jams · 3D Printing Stack Exchange, 2020 · 4 posts · answered on VLKI’s post, CC BY-SA 4.0

…After the trigger the printer continued downwards for another 3-4 inches, this would put the head below the bed if I let the…

Still open · 3DTouch activating but responding too late · 3D Printing Stack Exchange, 2020 · 1 posts · answered on Michael’s post, CC BY-SA 4.0

…I'm not sure how to get the holes for the dowels and bed bolt to all be parallel and level so that they…

Still open · Options for attaching bed legs at an angle · Woodworking Stack Exchange, 2021 · 3 posts · answered on Toby Kathan’s post, CC BY-SA 4.0

…You need to correct the bed leveling on that corner (too low) Also, the better part doesn't look right either. You can see…

Still open · Sunken and rough bottom layer · 3D Printing Stack Exchange, 2019 · 3 posts · answered on Thomas Weller’s post, CC BY-SA 4.0

…You want to make sure it is as level as possible and a good tip is to raise your bed just so slightly than…

Still open · Printing with Polycarbonate keeps warping · 3D Printing Stack Exchange, 2018 · 4 posts · answered on Juan Pablo Rodas Martínez’s post, CC BY-SA 4.0

…I have a similar file that allows me to level the bed without a computer by just moving the nozzle around to a few…

Still open · How do people load filament, prime the printhead, flush out the old filament when changing colors when using a standalone 3D printer? · 3D Printing Stack Exchange, 2016 · 8 posts · answered on Dimitri Modderman’s post, CC BY-SA 4.0

…For now, I intend to level the bed manually. Well the issue I'm having now is that after flashing the firmware (Marlin Firmware…

Still open · Z-axis endstop not functioning after Marlin Firmware installation · 3D Printing Stack Exchange, 2018 · 2 posts · answered on Jeff Clark’s post, CC BY-SA 4.0

…My print bed is probably bent down in the middle as per the sheet of paper leveling and I'm wondering if the x…

Still open · PLA Print fail - Stringing and underextrusion · 3D Printing Stack Exchange, 2024 · 2 posts · answered on Sp00n’s post, CC BY-SA 4.0

…The "standard" process for doing so was to remove the bed from the printer and freeze it. I found that dry ice worked just…

Still open · Can I leave the backing on a stick-on mat and use binder clips instead? · 3D Printing Stack Exchange, 2025 · 3 posts · answered on Joel Coehoorn’s post, CC BY-SA 4.0

…Got it all put together last night and ran all the basic setups including an auto bed leveling. This feature is both a blessing…

Still open · AnyCubic D (aka Predator) - Z-zeroing and first layer issues · 3D Printing Stack Exchange, 2020 · 4 posts · answered on KeithS’s post, CC BY-SA 4.0

…tuning of the bed : your bed should be super-flat and perfectly leveled. Use an indicator gauge if you can. filament chemistry : that is…

Still open · How can I get PLA or PETG to stick to a glass bed permanently without adhesives? · 3D Printing Stack Exchange, 2018 · 2 posts · answered on Benjamin Samuel Goldschmidt’s post, CC BY-SA 4.0

…After messing around for the last couple of days with bed leveling, I'm finally able to get consistent first level all thought I…

Still open · Ender 5 Printing Issues · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Vladimir Oselsky’s post, CC BY-SA 4.0

…Homing movement of XYZ Bed leveling Heating test to 200 °C Extrusion of some millimeters Retract some millimeters That solves the basic mechanical side…

Still open · Order of solving printing issues · 3D Printing Stack Exchange, 2019 · 4 posts · answered on Luke Dunn’s post, CC BY-SA 4.0

…However, the moving bed results in severe vibration. I need anti-vibration or stabilization methods for my very light Raspberry Pi camera. I was…

Still open · How to reduce vibration on a camera arm connected to the printer bed? · 3D Printing Stack Exchange, 2023 · 4 posts · answered on Bob Ortiz’s post, CC BY-SA 4.0

…as I try to home ONLY the Z axis to level the bed, the printer automatically moves the nozzle to the X0 Y0 after…

Still open · Anet A6 Firmware · 3D Printing Stack Exchange, 2018 · 2 posts · answered on Felix Hauser’s post, CC BY-SA 4.0

…Belts are sufficiently tight, the bed is level, the printer is on a flat sturdy table, and I still have this issue. Thanks for…

Still open · Ender 3 V2 really bad layer shifting · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Dominic B.’s post, CC BY-SA 4.0