bed leveling keeps drifting

…Also, try doing a levelling of the bed. I have found that if my nozzle is too low, and scraping on the bed then…

Still open · My 3D printer's extruder doesn't work · 3D Printing Stack Exchange, 2024 · 2 posts · answered on Nathan Vidal’s post, CC BY-SA 4.0

…Search online for: "3D printer bed leveling": the procedure is normally the same for most printers , but if your model is a common one…

Still open · 3d Print pops off before complete · 3D Printing Stack Exchange, 2018 · 2 posts · answered on Xander1111’s post, CC BY-SA 4.0

…What options are left? Was there PLA stuck inside the hot bed that's holding the nozzle? I heated it to printing levels to…

Still open · How to remove a stripped nozzle · 3D Printing Stack Exchange, 2020 · 1 posts · answered on DeeV’s post, CC BY-SA 4.0

…In Ultimaker Cura I use the jog buttons (like I always do when leveling the bed) but every time I do this it seems…

Still open · Z-axis of Anet A8 always moves additional 5 mm upwards when moving X and Y-axis in Ultimaker Cura · 3D Printing Stack Exchange, 2019 · 2 posts · answered on Mirco’s post, CC BY-SA 4.0

…I've been exploring many different styles of printers and found this type of printer that has a fixed bed that stays fixed in…

Still open · Why aren't fixed build platform 3D printers popular? · 3D Printing Stack Exchange, 2023 · 6 posts · answered on Faraz Ahmed’s post, CC BY-SA 4.0

…I have also leveled the bed after every few prints just to be safe. What seems to consistently happen when I print is that…

Still open · Issues printing with colorFabb wood PLA on Ender 5 Pro · 3D Printing Stack Exchange, 2023 · 1 posts · answered on Michael McCauley’s post, CC BY-SA 4.0

…My first attempt had it lifting from the bed before a few layers had completed. When I tried it with a thin brim on…

Still open · Help printing in ABS · 3D Printing Stack Exchange, 2021 · 4 posts · answered on Mark Booth’s post, CC BY-SA 4.0

…It will successfully complete the "auto home" sequence but not the "level bed" sequence. For troubleshooting, I have tried a different leveling sensor I…

Still open · Ender 3 Pro with BLTouch, partially completes ABL sequence then locks up · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Liam Kaiser’s post, CC BY-SA 4.0

I've just got an Ender-3 Pro printer and set it up according to general recommendations, including bed leveling (I used the "paper…

Still open · The print broke into tangled filaments · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Sogawa-sps’s post, CC BY-SA 4.0

…some mesh data (poor mesh data because I haven't levelled the bed but that's not the main issue). If I then repeatedly…

Still open · While heating, BLTouch mesh data gets worse and worse the more times you probe · 3D Printing Stack Exchange, 2023 · 3 posts · answered on DreamingInsanity’s post, CC BY-SA 4.0

…I have an Ender-3 and use PLA with a 200 °C nozzle temp and 60 °C bed temp. When leveling, I've been…

Still open · My first layer becomes solid when sections are supposed to have small separations · 3D Printing Stack Exchange, 2020 · 2 posts · answered on StarNamer’s post, CC BY-SA 4.0

…bed leveling) that would be accessible from a computer rather than from the LCD menu on the printer. In a slightly similar vein I…

Still open · Is there a convenient GUI tool for configuring Marlin settings? · 3D Printing Stack Exchange, 2020 · 1 posts · answered on Shwouchk’s post, CC BY-SA 4.0

…after the G28 instruction) will tell the printer to use the auto bed leveling. Once I did that, the printer started working as expected.

Still open · CR Touch firmware NO Z-axis home Ender 5 Pro 4.2.7 · 3D Printing Stack Exchange, 2022 · 4 posts · answered on Just noobit 3d’s post, CC BY-SA 4.0

I have been reading that glass plates are really good, and the bed plates with the Makerbot Replicator+ are all not so good (I…

Still open · Can I put a glass plate in a Replicator+? · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Jesse’s post, CC BY-SA 4.0

…1 s The vat/FEP film was tightened down nicely, the print bed auto-levels before every print. The Question: 'Simply', why have I…

Still open · Resin LCD prints ending up with random holes in them · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Adzi B’s post, CC BY-SA 4.0

…I have a BLTouch probe and have leveled my bed multiple times with the built-in feature, and with paper. Also if it helps…

Still open · Why is my printer overextruding at one end of one layer? · 3D Printing Stack Exchange, 2024 · 3 posts · answered on Useer_1782’s post, CC BY-SA 4.0

…pump inlet, but that assumes that the engine stays level - like on a test bed. But real engines don’t do that because of…

Still open · Running car on low oil · Motor Vehicle Maintenance & Repair, 2020 · 2 posts · answered on Nicholas Scott Megesi’s post, CC BY-SA 4.0

…First of all, I would make sure that my bed is properly leveled. Download one of the bed level tests and keep adjusting until…

Still open · What is causing these severe print errors on an Ender 3? · 3D Printing Stack Exchange, 2022 · 2 posts · answered on when squared equals a negative’s post, CC BY-SA 4.0

…Misc Bed is manually leveled by adjusting screws and nuts Glass is held to the bed by small aligator clips I print on bare…

Still open · What kind of problem is this? How does it correct itself? · 3D Printing Stack Exchange, 2020 · 3 posts · answered on YetAnotherRandomUser’s post, CC BY-SA 4.0

…I did some searching online, and following the recommendations I saw, I re-leveled the print bed, did my best to clean the extruder…

Still open · How do I stop the extruder from sticking to the back corner of the part? · 3D Printing Stack Exchange, 2024 · 1 posts · answered on Lawton’s post, CC BY-SA 4.0