bed leveling keeps drifting

…I've leveled the bed and have been fiddling with the Z-offset yet my prints still fail. Weirdly enough, the 3D prints seem…

Still open · 3D Print Failing With Extruder Not Extruding After a While · 3D Printing Stack Exchange, 2023 · 1 posts · answered on A Cloudy Hill’s post, CC BY-SA 4.0

…The firmware does not need to be updated, and the bed is level. I do not know what else the reason could be. Would…

Still open · Printer stops printing at the same spot for every model · 3D Printing Stack Exchange, 2022 · 2 posts · answered on CKPrintissues’s post, CC BY-SA 4.0

…a E3D V6 hotend that when using the same settings and bed-leveling/z-distance-setting procedures, that the filament is much more likely…

Still open · E3D V6 nozzle vs MK8 nozzle, first layer adhesion · 3D Printing Stack Exchange, 2023 · 3 posts · answered on cds333’s post, CC BY-SA 4.0

…It is probably a board-level (not chip level) problem Assuming the configuration is good, it is likely that there has been a (repairable…

Still open · Stepper motor driver dead? · 3D Printing Stack Exchange, 2021 · 2 posts · answered on tomaz’s post, CC BY-SA 4.0

…200 °C Bed: 50 °C Filament: GiantArm PLA They're caused by filament being pulled during travel so they qualify as stringing. You need…

Still open · Some kind of stringing · 3D Printing Stack Exchange, 2022 · 3 posts · answered on tmighty’s post, CC BY-SA 4.0

…I'm printing in Amazon Basics PLA, nozzle at 200 °C, bed at 55 °C. I level the bed with a 0.08 mm…

Still open · How can I correct *second and third layer* elephant foot? · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Zeiss Ikon’s post, CC BY-SA 4.0

…with 3 Z motors for automatic true leveling, rely on gravity to move/hold the bed in the -Z direction and only drive the…

Still open · Will 3D printing work upside down or in zero gravity? · 3D Printing Stack Exchange, 2021 · 6 posts · answered on BetterSense’s post, CC BY-SA 4.0

…magnetic bed sticker with a new one as the adhesion on the initial layer was poor even though the bed looked level. Once I…

Still open · Delamination issue Ender 3 Pro PLA · 3D Printing Stack Exchange, 2020 · 3 posts · answered on user3573036’s post, CC BY-SA 4.0

When I test #2 against the 90 degrees of a carpenter square is dead on ! The digital level is not that stable and I…

…mm of the PTFE tube, I performed cold pulls, I leveled my bed before every print, made the line width in the profile 0…

Still open · Ender 3 underextrusion · 3D Printing Stack Exchange, 2020 · 2 posts · answered on David Hyun’s post, CC BY-SA 4.0

…check difference and adjust E step/mm accordingly) Performed an auto bed leveling I even halved my flow rate in the slicer (Ultimaker Cura…

Still open · Can't seem to fix over extrusion · 3D Printing Stack Exchange, 2019 · 4 posts · answered on Mikelo’s post, CC BY-SA 4.0

…bed levelling is not magic , and a little more complicated to start with, if you order a printer without an auto bed levelling sensor…

Still open · First time assemble of Anet A6 printer. Only fan works · 3D Printing Stack Exchange, 2018 · 2 posts · answered on Tactrophyc’s post, CC BY-SA 4.0

…lowering heated bed temperature by 5 °C each print, print with a raft and increasing the nozzle to build plate distance (leveling with a…

Still open · Trouble printing perpendicular walls · 3D Printing Stack Exchange, 2021 · 5 posts · answered on rrirower’s post, CC BY-SA 4.0

…When I click "level bed" it moves to homing the X and Y axes to 0 and to the middle but the probe does…

Still open · BLTouch problem with pin deployment · 3D Printing Stack Exchange, 2024 · 2 posts · answered on Akumulator’s post, CC BY-SA 4.0

Just assembled my Ender 3, was homing the Z Axis and Leveling the bed, etc. During which I heard this high pitched noise that…

Still open · Strange Z-Axis Noise on New Ender 3 · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Joshua Gray’s post, CC BY-SA 4.0

…I have leveled multiple times, checked my extruder settings within my slicer where I adjusted the extrusion multiplier to 105 % as I thought this…

Still open · First layer inconsistency · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Josh Jagessar’s post, CC BY-SA 4.0

…I have spent so many hours of every day, leveling the printer time and time again, I cleaned it up, checked for loose screws…

Still open · 3D printer is not printing as well as it used to · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Ryan Vella’s post, CC BY-SA 4.0

…Is this 'bedding in' and do I need to be patient or is something wrong? Note I have checked the reservoir and the level…

Still open · New pads, old discs - pedal travel bad when engine running · Motor Vehicle Maintenance & Repair, 2019 · 2 posts · answered on 8bitjunkie’s post, CC BY-SA 4.0

…The printer will successfully go through auto leveling and the clean/prep line on the left side. When the line finished I see the…

Still open · Marlin 2.1 reboots before printing model when power recovery is enabled · 3D Printing Stack Exchange, 2022 · 2 posts · answered on Dave’s post, CC BY-SA 4.0

…I used a level to ensure the bed is flat. I'm using a glass bed with great adhesion (clearly; the model breaks before…

Still open · Extruder keeps crashing into print · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Micah Henning’s post, CC BY-SA 4.0