bed leveling keeps drifting

…I auto homed and used the bed leveling mechanism built in one many times. Any suggestions why the height of the printed part is…

Still open · Creality CR10 S5; the Z dimension is wrong after switch from 0.4 to 0.2 mm nozzle · 3D Printing Stack Exchange, 2019 · 1 posts · answered on cybernard’s post, CC BY-SA 4.0

…All I've recently done is install a new cartridge and thermistor, and everything was working totally fine until I re-leveled my bed…

Still open · Ender 3 X Axis stops moving mid print at random times, only makes Y movements after · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Brandon Thomas’s post, CC BY-SA 4.0

…PLA only printers are usually a few cheaper because they do not have heat bed. availability of support: official support, community size, market penetration…

Still open · Which 3D printer is good for beginners? · 3D Printing Stack Exchange, 2017 · 4 posts · answered on addyc1986’s post, CC BY-SA 4.0

…It appears that the other printer functions exist, I was able to run the bed leveling processes successfully, just no text is present to…

Still open · How to restore languages to Creality CR-6 SE after firmware update? · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Dapper’s post, CC BY-SA 4.0

…From attached pictures I can see that some of the printouts are not sticking enough to the bed (that can be a non-leveled…

Still open · Creality CR-10 Clogs and Underextrusion - Filament at fault? · 3D Printing Stack Exchange, 2018 · 3 posts · answered on arunabha42’s post, CC BY-SA 4.0

…I was having some massive issues and determined that my leveling was off because the BLTouch was flashing red and not connecting. When I…

Still open · How do I know if my BLTouch is faulty or firmware is faulty? · 3D Printing Stack Exchange, 2021 · 3 posts · answered on Cayce K’s post, CC BY-SA 4.0

…I've switched to a glass plate and triple checked that it is level. I checked to see if it was binding but honestly…

Still open · Z-Axis raising and dropping substantially during print knocking print off · 3D Printing Stack Exchange, 2019 · 2 posts · answered on Krystal’s post, CC BY-SA 4.0

For some recent prints I have been using rafts as generated by Cura to aid in bed adhesion; which helps, but is not as…

Still open · Alternative raft generation · 3D Printing Stack Exchange, 2019 · 1 posts · answered on Eelco Hoogendoorn’s post, CC BY-SA 4.0

…High level Mechanical Firmware Software repeat Mechanical Level everything. Bed. The X axis. Make sure there is no binding, etc. Also make sure the…

Still open · Calibrating steps/order · 3D Printing Stack Exchange, 2017 · 3 posts · answered on Thomas S.’s post, CC BY-SA 4.0

…The printer heats up, auto bed levels, and starts the print. However, after a couple minutes (usually after the 1 st or 2 nd…

Still open · Printer crashes at the beginning of a print · 3D Printing Stack Exchange, 2023 · 4 posts · answered on Rosalie W’s post, CC BY-SA 4.0

…I tightened the belts and leveled the plate. I have a Creality Ender 3 which I use together with UltiMaker Cura slicer. I print…

Still open · terrible quality on Ender 3 · 3D Printing Stack Exchange, 2023 · 3 posts · answered on MK.’s post, CC BY-SA 4.0

…However, during bed leveling, it failed and went into the "some problem encountered" state again. To allow negative axis values, usually, the way is…

Still open · Moving the Z-axis stepper motors below Z 0.0 · 3D Printing Stack Exchange, 2018 · 2 posts · answered on Thomas Weller’s post, CC BY-SA 4.0

…Frequently, after levelling the bed, the tool head is raised in Z direction with a low speed (movement in Z direction is always much…

Still open · Slow speed of the delta 3D printer · 3D Printing Stack Exchange, 2020 · 2 posts · answered on Mj996’s post, CC BY-SA 4.0

…I only uncommented my printer model and a couple of features of the firmware; nothing involving speed (mainly the mesh bed leveling). Is it…

Still open · Do firmware updates affect print speeds? · 3D Printing Stack Exchange, 2019 · 3 posts · answered on Lux Claridge’s post, CC BY-SA 4.0

…Personally I didn't measure anything, I've just made sure my bed is level and adjusted z-offset bit by bit until I…

Still open · Z-offset: 0.2 mm, 0.1 mm or the thickness of paper? · 3D Printing Stack Exchange, 2022 · 3 posts · answered on Byte Insight’s post, CC BY-SA 4.0

…I tried cleaning the gear, levelling and cleaning the bed with almost no success. I'm using a Creality Ender 3 with a (golden…

Still open · Ender 3 doesn't extrude enough? · 3D Printing Stack Exchange, 2022 · 3 posts · answered on Kilian Lorenzen’s post, CC BY-SA 4.0

Using TH3D firmware with some small changes to allow manual mesh levelling and to increase the serial baud rate, neither of which are active…

Still open · Ender 3 not allowing z=0 regardless of z offset value · 3D Printing Stack Exchange, 2022 · 2 posts · answered on thomasaronford’s post, CC BY-SA 4.0

…Know use PLA Plus or (PLA+)due to not sticking to the bed well enough and your issue. And this issue may be the…

Still open · Filament jam on the tube entrance · 3D Printing Stack Exchange, 2021 · 4 posts · answered on Hola Soy Edu Feliz Navidad’s post, CC BY-SA 4.0

…That way I can see the effect of having it being printed on its side rather than perpendicular to the bed. "The first 3D…

Still open · What effects does the non-carthesian coordinate system have on the Part-design process for printing with a belt printer? · 3D Printing Stack Exchange, 2020 · 2 posts · answered on Trish’s post, CC BY-SA 4.0

…This is a video of what it does during a mesh bed leveling MBL (9 points): I upgraded the firmware to Marlin 2.0…

Still open · Big permanent layer shifts on X-axis, looks like something is holding the stepper motor but its not · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Rodolfo Coutinho’s post, CC BY-SA 4.0