bed leveling keeps drifting

…Printing with ABS and having it warp (probably bed temp) Trying to print a design with too thin a wall I think there is…

Still open · Why do 3D Printers Suck? Please share your user experience · 3D Printing Stack Exchange, 2017 · 3 posts · answered on AdamP’s post, CC BY-SA 4.0

…The rotors and pads were satisfactory (normal levels of rust on the rotors) before this 2 year period. The rotors and pads do not…

Still open · Do extremely rusty disc brake rotors/pads need to be replaced? · Motor Vehicle Maintenance & Repair, 2023 · 5 posts · answered on Amazon Dies In Darkness’s post, CC BY-SA 4.0

…I have done everything from leveling my bed as close as possible to the nozzle, slowing down the print speed to about half of…

Still open · Perimeters/shells not properly fusing - delamination · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Adrian’s post, CC BY-SA 4.0

…Alternate nozzle has been fastened, Bed leveling has been checked, Even used the other softwares to print. Reset-failsafe is also done. Conclusion: Feeding…

Still open · Extrusion is not continuous · 3D Printing Stack Exchange, 2018 · 3 posts · answered on shachin_vs’s post, CC BY-SA 4.0

…and bed size, fairly similar results with both, mainly this issue is present on both slicers BLTouch, though the bed is manually leveled to…

Still open · Inconsistent layer stacking · 3D Printing Stack Exchange, 2021 · 1 posts · answered on Matt’s post, CC BY-SA 4.0

…After struggling for days on bed levelling, I came out with an almost decent alignment. So I printed the well-known boat to test…

Still open · Help to find out all the failures in first IDEX test · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Mark’s post, CC BY-SA 4.0

…Some engine test beds have priming pumps for fuel and oil and some of our lab engines at university had oil priming pumps fitted…

Still open · Sufficient Oil Distribution after Cranking for a Long Time? · Motor Vehicle Maintenance & Repair, 2020 · 3 posts · answered on AaronD’s post, CC BY-SA 4.0

…Change the nozzle Set the bed level (like a million times) Download calibration files (e.g calibration squares) I have used Cura with the…

Still open · Print gets worse with every layer - Ender 3 · 3D Printing Stack Exchange, 2021 · 4 posts · answered on Xnob’s post, CC BY-SA 4.0

…a very uniform, level top surface specially finished for floor tiles. (2) heavy red clay body for compression resistance. (3) bedded fully in a…

Still open · How to reduce breaking of tiles indoors, when operating an electric tow truck · Motor Vehicle Maintenance & Repair, 2016 · 4 posts · answered on user4820’s post, CC BY-SA 4.0

…The idea being that more plastic and height in the initial layer makes it less temperamental as far as bed leveling goes, and it…

Still open · First layer rippling and no filament in certain areas · 3D Printing Stack Exchange, 2022 · 4 posts · answered on Hellwhisper’s post, CC BY-SA 4.0

…Releveling the bed. I did this several times, using this Creality Service tutorial video : lower nozzle to 0 mm, adjust Z-offset until I…

Still open · Why are flat sections printing rough? · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Magua’s post, CC BY-SA 4.0

…I also tried printing at hotter and cooler temperatures, with and without the heated bed, and printing at slower speeds, but all of these…

Still open · Creality CR-10 extruder clicking and/or nozzle clogging · 3D Printing Stack Exchange, 2019 · 2 posts · answered on CouscousKingpin’s post, CC BY-SA 4.0

…Leveled the bed with feeler gauges on all 4 furthest corners, I started with 0.2 mm and moved it so it's just…

Still open · I adjusted the E-steps from 93 to 117.8, now it retracts all filament · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Anthony Powell’s post, CC BY-SA 4.0

…The only remote concern is the increased level of humidity released by the dirt vs pavement. If you plan to move the vehicle regularly…

Still open · Is it harmful to a car to be parked on gravel and mud instead of pavement? · Motor Vehicle Maintenance & Repair, 2018 · 2 posts · answered on Soufiane N’s post, CC BY-SA 4.0

…Quality levels (aka built-in profiles). Custom profiles. Settings not yet saved to a profile. In the Cura GUI, once a setting has been…

Still open · Temperature settings not changing in Cura · 3D Printing Stack Exchange, 2019 · 2 posts · answered on N. Virgo’s post, CC BY-SA 4.0

…provide more constant light levels for a webcam; possibly some joy sticks to manually maneuver the extruder and bed; etc. Basically I want something…

Still open · Upgrading printer controller · 3D Printing Stack Exchange, 2020 · 4 posts · answered on Rekamanon’s post, CC BY-SA 4.0

…But the T-Rex has a Bltouch and it goes to the middle of the bed to home the Z-axis. This is due…

Still open · How do I change Z safe homing coordinates in the G-code , not in Marlin · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Kirk D’s post, CC BY-SA 4.0

…2mm layer height 0.4mm line width 210ºC extrusion temp 60ºC Bed temp 40mm/s print speed Fusion 360, Cura 2.7 or 4…

Still open · PLA printings always ~0.22% larger · 3D Printing Stack Exchange, 2019 · 4 posts · answered on rccursach’s post, CC BY-SA 4.0

…What the heck, I'll add auto bed leveling. I install the BLTouch. Plug it in and no power (in my defense, I forgot…

Still open · RAMPS 1.6 VCC and 5 V jumper issues · 3D Printing Stack Exchange, 2023 · 2 posts · answered on allen476’s post, CC BY-SA 4.0

…The observations above apply to both the X and Y axis, but the X axis is so light that it requires extreme levels of…

Still open · Are resonances of belt driven carriage strongly direction dependent? Mitigations? · 3D Printing Stack Exchange, 2022 · 2 posts · answered on R.. GitHub STOP HELPING ICE’s post, CC BY-SA 4.0