first layer not sticking to the bed

…bed so quickly and rolled just after the nozzle - and slowing down almost always helped. You may also decrease height of first layer e…

Still open · Filament sticks to nozzle · 3D Printing Stack Exchange, 2021 · 3 posts · answered on Eric Brochu’s post, CC BY-SA 4.0

…Then all of a sudden I can't get them to stick and the first layer looks wavy and weird. After a few tokens…

Still open · First layer looks weird and print fails · 3D Printing Stack Exchange, 2020 · 5 posts · answered on GusOst’s post, CC BY-SA 4.0

…First layer adhesion is depends critically on an accurate first layer thickness, which depends on the bed height calibration. Adding or, perhaps more critically…

Still open · Polypropylene Bed Adhesion · 3D Printing Stack Exchange, 2019 · 3 posts · answered on dornadigital’s post, CC BY-SA 4.0

…Sometimes, increasing the bed and filament temperature with 5 °C for the first layer also helps. Also check your speed settings. 1st layer should…

Still open · Filament moving around and not sticking to bed · 3D Printing Stack Exchange, 2019 · 4 posts · answered on Andrew Hawkins’s post, CC BY-SA 4.0

…first layer. Values of 120-140% are standard settings for improving adhesion. Slightly increasing height of initial layer may also help to overcome bed…

Still open · How to get Sunlu PLA to adhere to the printing bed? · 3D Printing Stack Exchange, 2021 · 4 posts · answered on Anonymous _User’s post, CC BY-SA 4.0

…Fan speed at 100 % from the first layer. The whole setup works flawlessly with PLA at 210 °C with a heated bed at 35…

Still open · How is it possible for (PHA) prints to warp on an unheated bed? · 3D Printing Stack Exchange, 2025 · 3 posts · answered on Bob Ortiz’s post, CC BY-SA 4.0

…If the brim isn't sticking, use a higher bed temperature for the first layer. If the brim comes up only on one side…

Still open · PLA print warping on heated bed · 3D Printing Stack Exchange, 2019 · 3 posts · answered on Emile D.’s post, CC BY-SA 4.0

Usually I had problems with the adhesion of the first layers, and most questions here and out there are about this issue. Instead now…

Still open · ABS does not stick AFTER some good layers · 3D Printing Stack Exchange, 2022 · 1 posts · answered on Mark’s post, CC BY-SA 4.0

…the first layer of the raft (which by the way is totally unnecessary for PLA) the nozzle is too far from the bed, you…

Still open · Prints not sticking to bed or just not extruding? · 3D Printing Stack Exchange, 2022 · 4 posts · answered on Jim’s post, CC BY-SA 4.0

…and part cooling during bottom layer printing affect bed adhesion when dealing with generic PLA? For the first layer for PLA, you want slow…

Still open · How do flow rate and part cooling affect bed adhesion in PLA? · 3D Printing Stack Exchange, 2023 · 2 posts · answered on Aaargh Zombies’s post, CC BY-SA 4.0

…first layer is not sticking well to the bed it can be caused by several issues. Usually the height of the first layer plays…

Still open · Adhesion problem (heat bed or extruder issue) · 3D Printing Stack Exchange, 2018 · 2 posts · answered on dale’s post, CC BY-SA 4.0

…difficulty printing first layer of an object with support. The object has a few curved surfaces that touch the print bed, so not a…

Still open · Support material first layer adhesion issues · 3D Printing Stack Exchange, 2019 · 5 posts · answered on AndrewP’s post, CC BY-SA 4.0

…Also bed leveling is super important as are your print settings. What you want for the first layer is to have it essentially "pushing…

Still open · PLA and bed heating? · 3D Printing Stack Exchange, 2019 · 12 posts · answered on Thomas S.’s post, CC BY-SA 4.0

…bed while the extruder is moving. I think my first layer is maybe not going down well enough, though the pieces that do stick…

Still open · Small parts de-adhere halfway through print · 3D Printing Stack Exchange, 2023 · 3 posts · answered on javanix’s post, CC BY-SA 4.0

…Through all my tests it takes 80 °C to get the first layer to stick and if I reduce temp to 60 °C after…

Still open · Acceptable temperature variation in heated bed · 3D Printing Stack Exchange, 2021 · 2 posts · answered on David Pearson’s post, CC BY-SA 4.0

…Consider to edit your post to include the layer heights and also the filament type and filament and bed temperatures. My first instinct is…

Still open · What is this called and how do I avoid it? (model frees itself from support structure and warps upwards) · 3D Printing Stack Exchange, 2022 · 5 posts · answered on tmighty’s post, CC BY-SA 4.0

…first layer 235 °C, other layers 230 °C. Bed: First layer 65 °C, other layers 60 °C. Fan: Disable fan for the first: 3…

Still open · The nozzle keeps clogging, midway through the print while printing with PETG filament · 3D Printing Stack Exchange, 2022 · 1 posts · answered on Shubham’s post, CC BY-SA 4.0

…The primary objective of a slower print speed for the first one to two layers is to ensure a bonding to the build plate…

Still open · Bottom layer print speed - When do you reach diminishing returns? · 3D Printing Stack Exchange, 2022 · 2 posts · answered on Aaargh Zombies’s post, CC BY-SA 4.0

…system which uses a PEX layer over flex steel (which sticks to a magnetic sheet on the printer bed). To clean old material off…

Still open · How would you clean/prepare a flexible/magnetic mat (e.g. Ender 5) as compared to a glass bed? · 3D Printing Stack Exchange, 2019 · 3 posts · answered on Oliver Giesen’s post, CC BY-SA 4.0

…as glue stick or hairspray on the bed. Print Speed and Cooling Adjustments : Reduce the printing speed for the first few layers to allow…

Still open · Bad adhesion only when printing many small parts "all at once" - can't use Brim · 3D Printing Stack Exchange, 2023 · 2 posts · answered on SF.’s post, CC BY-SA 4.0