warping corners lifting off the bed

16 threads discussed this. Here is what worked. 512 ms

1. There are many different approaches to solving this issue and most of the answers already are spot-on. However, the fundamental reason for the "warping" is incorrect and inconsistent temperature across the material.

   Marked as the answer · Why do the corners of my ABS object lift off the bed? · 3D Printing Stack Exchange, 2018 · 12 posts · answered on Kevin Morse’s post, CC BY-SA 4.0

2. I would guess that there are two possible sources for the problem. First, your long board may be warping. This will be the result of grain direction or stress due to humidity/moisture changes.

   Marked as the answer · How do I fix a warped shoji door? · Woodworking Stack Exchange, 2017 · 3 posts · answered on MiniMe’s post, CC BY-SA 4.0

3. In short, yes, it helps a little. Curves provide less surface area per unit volume (a sphere has the least possible surface area relative to the volume of the solid), and that reduces the rate at which the material in…

   Marked as the answer · Does having more curvier corners help warping more then smaller curves · 3D Printing Stack Exchange, 2020 · 2 posts · answered on Ageis’s post, CC BY-SA 4.0

4. Cool environmental conditions are the single biggest contributor to ABS delamination. Delamination or edge/corner cracking is caused by warping stresses when the first layer adhesion is stronger than the interlayer…

   Marked as the answer · Layer delamination · 3D Printing Stack Exchange, 2019 · 5 posts · answered on tbm0115’s post, CC BY-SA 4.0

5. While I tried a lot of things to solve this, including tuning temperature, fan, speed, etc., ultimately the single biggest factor that causes or prevents it is the state of Cura's Outer Before Inner Walls (…

   Marked as the answer · How do you solve PLA corner-curling short of printing really, REALLY slow? · 3D Printing Stack Exchange, 2020 · 3 posts · answered on R.. GitHub STOP HELPING ICE’s post, CC BY-SA 4.0

6. The only time I've seen lifting, away from the edges of the part like this, is when the bed is contaminated with something which will stop the print sticking, like fingerprints and such.

   Marked as the answer · Irregular adhesion on Creality glass bed · 3D Printing Stack Exchange, 2021 · 3 posts · answered on geNAZt’s post, CC BY-SA 4.0

7. Since nobody had any idea what cause the problem, I investigated for a full week. The problem is related to Fade Height and .... a warp bed , since I have ABL (Auto Bed Levelling) and Fade Height enable.

   Marked as the answer · Height of the prints are always larger · 3D Printing Stack Exchange, 2021 · 2 posts · answered on Stefan Merfu’s post, CC BY-SA 4.0

8. Everybody's combination of fan hardware and print settings is different. Unless someone else has the exact same printer and slicer profiles as you, there's no way to really say anything like "use X% for PLA" or…

   Marked as the answer · How to utilize/calibrate print fans for PLA? · 3D Printing Stack Exchange, 2016 · 4 posts · answered on kamuro’s post, CC BY-SA 4.0

9. I was hoping for some magic solution, but Graphus indicated in the comments that wedges were indeed the way to go. Then I realized I could clamp the wedges to the bench top.

   Reported as working · Immobilizing a cupped board when traversing · Woodworking Stack Exchange, 2025 · 2 posts · answered on stanch’s post, CC BY-SA 4.0

10. …eg, around the edges, jammed between a lifting corner and the bed. With a fixed bed, this can be done without pausing the printer…

    Still open · What can I do about a printjob in progress that starts to warp/curl on the edges? · 3D Printing Stack Exchange, 2024 · 5 posts · answered on Adam Plocher’s post, CC BY-SA 4.0

11. …the layers separate, usually at or near a corner. My first attempt had it lifting from the bed before a few layers had completed…

    Still open · Help printing in ABS · 3D Printing Stack Exchange, 2021 · 4 posts · answered on Mark Booth’s post, CC BY-SA 4.0

12. …you don't keep it from lifting up. If it lifts up it means that the part is warping significantly, and blue tape has…

    Still open · What do you use to keep your blue tape from lifting? · 3D Printing Stack Exchange, 2022 · 7 posts · answered on kane’s post, CC BY-SA 4.0

13. …the magnetic build sheet, potentially causing prints to lift or warp at +X +Y corner). What I found was that the brackets I had…

    Still open · My FlashForge Creator Pro has started to spontaneously restart mid-print, begin vibrating, printing along one axis repeatedly, etc · 3D Printing Stack Exchange, 2022 · 3 posts · answered on Chuck Crawford’s post, CC BY-SA 4.0

14. …The corners are not curling up this is the center of the print lifting. I started printing at 25% infill but have tried 100…

    Still open · Large flat ABS print curling during cooldown · 3D Printing Stack Exchange, 2016 · 2 posts · answered on jmb2341’s post, CC BY-SA 4.0

15. …If both front wheels are lifted the tire should be able to move. b. If only one front wheel is lifted, the tire shouldn…

    Still open · Speed-Dependent Hum/Whine and Vibrations after a Locked-Wheels Hard Brake and Skid · Motor Vehicle Maintenance & Repair, 2018 · 3 posts · answered on Sagie’s post, CC BY-SA 4.0

16. …On the downside, you might experience issues with the tape itself lifting from the bed when printing parts that wrap a lot. A wide…

    Still open · What is a good strategy for removing 3d prints from an UNheated Glass bed? · 3D Printing Stack Exchange, 2016 · 4 posts · answered on Curtis’s post, CC BY-SA 4.0